• Show Sidebar

There are 1000 products.

Active filters

  • Categories: BGA Soldering Preheating Station
  • Categories: Laptop Parts, Repair tool
  • Categories: Programmer & Sockets

OBDII BreaK Out Box Protocol Detector Diagnostic Tool

OBDII Protocol Detector & Break Out Box mainly used car OBD line signal judgment and signal transfer. Using car fault diagnosis instrument can quickly determine car OBD signal receiving. Signal may not meet angle can take other signal transfer angle. Application is very convenient and solve risks across the line.

Features:

1. In the process of using decoder, error can be found and diagnosed OBD connector link.

2. You can monitor the OBD interface voltage and ground, showed low voltage. Display diagnostic stitching error.

3. Jump for OBD interface signals. Signal lines such as decoder of 7 to 15 vehicles online.

4. Rapid detection of OBD2 diagnostic connector whether every stitch of the normal communication.

5. Replace the battery, save the car data function. When replace the battery, plug OBD2 connector into the car, at the same time connect additional power to the control box, so that ensure vehicle data is not lost.

This OBDII Protocol Detector & Break Out Box has wide range of applications in diagnostics, key programming and chip tuning:

- To monitor data steam while performing test on vehicle using a Scantool. This makes it possible for you to both execute a test and simultaneously monitor the testing process.

- Display testing voltage on the car or truck

- Display communicating pin number

- Is an extension of OBD Diagnostic Link Connector (DLC)

Packing List:

1pc x Break Out Box Interface

1pc x OBD pin Cable

1pc x Box

CH000491
€60.92

OBDII BreaK Out Box Protocol Detector Diagnostic Tool

BST8800E Repair Tools Kit Set ScrewDriver For Electronics PC Mobile Iphone PDA Tablet

Disassemble Tool

Brands: Best

Model: BST-8800E

Size: 4.3 x 5.7 x 0.7

Weight: 168g

Item Included: 10x Screw Drive - T3/T4/T5/T6/-2.0/Phillips 00/ Phillips 000/?0.8/?1.2/Y2.5/flat 2.0

Features:

1. The handle is made of ABS material with high hardness, good stability, resistance to environmental change

2. Carved stripes, beautiful, easy to draw the line and have non-slip

3. Flexible rotating nut, effectively improve the efficiency of

4. Batch mouth using high quality chrome vanadium steel, superior strength and toughness

5. High quality steel manufacturing, through the whole heat treatment, titanium plating, to ensure product quality

CH000314
€9.82

BST-8800E Repair Tools Kit Set ScrewDriver For Electronics PC Mobile Iphone PDA Tablet

TOP3000 Universal Programmer for MCU and EPROMs Programming ECU Chip Tunning

TOP3000 Auto Car Universal Programmer for MCU and EPROMs programming ECU Chip Tunning Tool

Login to Download: Download software

Specifications:

? Power supply input: 110 ~ 240VAC, 50/60Hz

? Power output: 5VDC, 2A

? Included: TOP3000 programmer,software CD, USB cable, power supply cable

Benefits:

? The TOP3000 programmer supports 2.5 ~ 6.5V devices

? Powered by your USB interface or the included 5V external power supply

? Fast transmission speed of 12MHz/s via the USB port

? Auto detects the device's manufacturer and part number

? Compatible with Notebooks and desktop computers

? The in-built connection inspection checks the connection for every pins in the unit

? Current protection function protects both the programmer and connected devices

? Has 48-pin self-lock sockets

? Compact programmer with tough plastic casing

Supports:

Actrans (EEPROM)

AMD (PLD, MPU, EPROM, EEPROM)

AMIC (EEPROM)

ASD (EEPROM)

Atmel (PLD, MPU, EPROM, EEPROM)

BDTIC (RAM)

Catalyst (EPROM, EEPROM)

Crescentec (MPU)

Dallas (RAM, MPU, EEPROM)

Elan (MPU)

EON (EEPROM)

EXEL (EEPROM)

Fujitsu (EPROM, EEPROM)

Future (MPU)

Hitachi (EPROM, EEPROM)

HMWIN (MPU)

Holtek (MPU)

Hynix (EEPROM)

Hyundai (EPROM)

ICT (EPROM)

Intel (MPU, RAM, EPROM, EEPROM)

ISSI (MPU, EEPROM)

Lattice (PLD)

LG (MPU)

Linksmart (EEPROM)

Macronix (EEPROM)

Matsushita (EPROM)

Megawin (MPU)

Micon (MPU)

Microchip (MPU, EPROM, EEPROM)

Mitsubishi (EPROM, EEPROM)

Mosel (MPU, EEPROM)

MXIC (EPROM, EEPROM)

NEC (EPROM, EEPROM)

NS (PLD, EPROM)

OKI (EPROM, EEPROM)

PDK (MPU)

Philips (MPU)

PMC (EEPROM)

PTC (EEPROM)

Ricoh (EPROM)

Samsung (MPU, EPROM, EEPROM)

SEEQ (EPROM, EEPROM)

SGS Thomson (PLD, EPROM, EEPROM)

Signetics (EPROM)

SMOS (EPROM

Sony (EPROM)

Sonix (MPU)

Spansion (EEPROM)

SST (MPU, EEPROM)

ST (EPROM, EEPROM)

STC (MPU)

Stand (RAM)

Syncmos (MPU, EEPROM)

TI (EPROM, EEPROM)

Topro (MPU)

Toptek (MPU)

Toshiba (EPROM, EEPROM)

Versachip (MPU)

VLSI (PLD, EPROM, EEPROM)

Winbond (MPU, RAM, EEPROM)

WSI (EPROM)

Xicor (EEPROM)

Package Include:

1pc x TOP3000 universal programmer

1pc x USB 2.0 cable (USB 1.1 compatible)

1pc x 5V/2A AC adapter

1pc x TOPwin software CD

1pc x English User Manual

CH000548
€98.21

TOP3000 Universal Programmer for MCU and EPROMs Programming ECU Chip Tunning

CM141 LeadFree Titanium Alloy Solder Soldering Pot Desoldering Bath 900W 110V

LEAD-FREE TITANIUM ALLOY SOLDERING POT

Operation instruction

Login to Download: * Manual Download

Our Lead-free titanium alloy soldering pot passed by SGS, built-in advanced microcomputer digital control and display system, make it more safe, more steady and more accurate. Its a good tool for electronic fields.

FEATURES:

* With big power heater, only within 25minutes to reach 450? from room temperature, (Different items with a little different heating time.)

* With advanced microcomputer digital control and double displays. make it more accurate heating and fast temperature returning capability.

* The boiler made of titanium alloy, can resist high temperature, cauterization and abrasion, largely prolong the life.

* With temperature setting and locking function, will not be affected by wrong operation.

* The setting value will be saved for long time, and can not be affected by power on or off. With auto sleeping function, prolong the machines life.

* With malfunction alarm.

Working conditions:

Working voltage: AC22010V

Working temperature: 0-55?

Working temperature: < 90% no dew

WARNING:

1. The soldering pot must be put on the balanced and ovenproof working desk, prevent the glowing tin go out of the pot. And also take care of the hot tin and the hot body.

2. Do not put other pb items together with the lead-free soldering pot, prevent pb pollution. If cause the products do not eligible, then we wont take on this liability.

3. It cant be used where it will be exposed to ignitable or corrosive materials and gases.

4. If you need to move the soldering pot, please turn off the switch and move it after the pot turn cool.

5. The pot is a hot equipment, if you no need to use, please shut off the switch, and put out the plug.

6. In order to keep it safe and prolong the life, its better stop working after it has worked more than 12hours.

7. Do not heating the pot when its empty, and use the power supplier with grounding cord.

8. The pot is made of titanium which import from Japan, after it is heated by hot temperature, the color will turn to golden or blue, its natural for the material.

OPERATION:

1. Set temperature:

Press the * button, the left LED will display ?,and the right LED will display numerical value, then press the + or -button, temperature will go up or down. Press * button, the value of temperature will be saved.

2. Microcomputer adjusting itself

If the temperature has obvious discrepancy, we can adjust the inside P, I, D value, it will make the pot with accurate control, the followings are two ways of P, I, D adjusting:

A. Auto adjusting

Keep pressing + button, then press * , the left LED will display AT; the right LED will display _ _ _. Then press ? or + change the _ _ _ to AT, this time please press * for 3 times, then the pot will begin P, I, D adjusting itself. Usually it will take for about 15-30 minutes to finish this adjusting, during this adjusting the temperature will fluctuate obviously, but its no wonder. Usually, we do not recommend the users use P, I, D adjusting.

B. Adjust the value of P, I, D by manual (Do not advise users use this way, its fit for the engineers who know P, I, D very well, otherwise maybe cause bad temperature control. If really need, we just recommend the first way.) The operation as follows: Keep pressing + , then press * , the LED will display above (A) setting mode, press * again the LED will display the value of P, I, D. Manual adjusting just can be set the original value.

Remarks: The original of P, I, D value is: P=20, I=80, D=20; If the temperature in

confusion, please set the P, I, D value as original value.

3. Calibration between display and real temperature.

After the heater was replaced or the sensor was oxidated, the temperature will occur warp, the users need to calibrate the pot termly, and as the follow steps:

A. Press CAL button (If your pot without this button, please open the front cover, there is a black button on the PCB of temperature control, that is CAL), the right LED will display OFF, keep pressing ? , and press * at the same time, the left LED will display LOC, the right LED will display -3-, then press * for 3 times (just this button, do not press any other buttons), the LED will display: The first time: Left ?H, right 999; The second time: Left ?L, right 0; The third time: Left ?L, then please input the value of temperature compensation. This value is the warp between display temperature and real temperature. For example, the real temperature is more 5? higher than the display temperature, it can use ? to set -5; If the real temperature is 5? less than the display temperature, it can use + to set 5.

B. The warp temperature is the value to input, after finish setting, press * again, the set value will be saved. Then press CAL (If your pot without this button, please open the front cover, there is a black button on the PCB of temperature control, that is CAL), it will come into the ordinary display mode.

TROUBLE SHOOTING:

1. Turn on the switch but no reflection, please check the fuse, and the plug.

2. The LED display setting temperature, but the pot temperature wont go up, it means that the heater is open circuit.

3. The pot display Err when the power switch is turned on, it means that the sensor is open circuit.

CH000318
€177.78

CM141 Lead-Free Titanium Alloy Solder Soldering Pot Desoldering Bath 900W 110V

OBDII BreaK Out Box Protocol Detector Diagnostic Tool

OBDII Protocol Detector & Break Out Box mainly used car OBD line signal judgment and signal transfer. Using car fault diagnosis instrument can quickly determine car OBD signal receiving. Signal may not meet angle can take other signal transfer angle. Application is very convenient and solve risks across the line.

Features:

1. In the process of using decoder, error can be found and diagnosed OBD connector link.

2. You can monitor the OBD interface voltage and ground, showed low voltage. Display diagnostic stitching error.

3. Jump for OBD interface signals. Signal lines such as decoder of 7 to 15 vehicles online.

4. Rapid detection of OBD2 diagnostic connector whether every stitch of the normal communication.

5. Replace the battery, save the car data function. When replace the battery, plug OBD2 connector into the car, at the same time connect additional power to the control box, so that ensure vehicle data is not lost.

This OBDII Protocol Detector & Break Out Box has wide range of applications in diagnostics, key programming and chip tuning:

- To monitor data steam while performing test on vehicle using a Scantool. This makes it possible for you to both execute a test and simultaneously monitor the testing process.

- Display testing voltage on the car or truck

- Display communicating pin number

- Is an extension of OBD Diagnostic Link Connector (DLC)

Packing List:

1pc x Break Out Box Interface

1pc x OBD pin Cable

1pc x Box

CH000491
€60.92

OBDII BreaK Out Box Protocol Detector Diagnostic Tool

BST8800E Repair Tools Kit Set ScrewDriver For Electronics PC Mobile Iphone PDA Tablet

Disassemble Tool

Brands: Best

Model: BST-8800E

Size: 4.3 x 5.7 x 0.7

Weight: 168g

Item Included: 10x Screw Drive - T3/T4/T5/T6/-2.0/Phillips 00/ Phillips 000/?0.8/?1.2/Y2.5/flat 2.0

Features:

1. The handle is made of ABS material with high hardness, good stability, resistance to environmental change

2. Carved stripes, beautiful, easy to draw the line and have non-slip

3. Flexible rotating nut, effectively improve the efficiency of

4. Batch mouth using high quality chrome vanadium steel, superior strength and toughness

5. High quality steel manufacturing, through the whole heat treatment, titanium plating, to ensure product quality

CH000314
€9.82

BST-8800E Repair Tools Kit Set ScrewDriver For Electronics PC Mobile Iphone PDA Tablet

TOP3000 Universal Programmer for MCU and EPROMs Programming ECU Chip Tunning

TOP3000 Auto Car Universal Programmer for MCU and EPROMs programming ECU Chip Tunning Tool

Login to Download: Download software

Specifications:

? Power supply input: 110 ~ 240VAC, 50/60Hz

? Power output: 5VDC, 2A

? Included: TOP3000 programmer,software CD, USB cable, power supply cable

Benefits:

? The TOP3000 programmer supports 2.5 ~ 6.5V devices

? Powered by your USB interface or the included 5V external power supply

? Fast transmission speed of 12MHz/s via the USB port

? Auto detects the device's manufacturer and part number

? Compatible with Notebooks and desktop computers

? The in-built connection inspection checks the connection for every pins in the unit

? Current protection function protects both the programmer and connected devices

? Has 48-pin self-lock sockets

? Compact programmer with tough plastic casing

Supports:

Actrans (EEPROM)

AMD (PLD, MPU, EPROM, EEPROM)

AMIC (EEPROM)

ASD (EEPROM)

Atmel (PLD, MPU, EPROM, EEPROM)

BDTIC (RAM)

Catalyst (EPROM, EEPROM)

Crescentec (MPU)

Dallas (RAM, MPU, EEPROM)

Elan (MPU)

EON (EEPROM)

EXEL (EEPROM)

Fujitsu (EPROM, EEPROM)

Future (MPU)

Hitachi (EPROM, EEPROM)

HMWIN (MPU)

Holtek (MPU)

Hynix (EEPROM)

Hyundai (EPROM)

ICT (EPROM)

Intel (MPU, RAM, EPROM, EEPROM)

ISSI (MPU, EEPROM)

Lattice (PLD)

LG (MPU)

Linksmart (EEPROM)

Macronix (EEPROM)

Matsushita (EPROM)

Megawin (MPU)

Micon (MPU)

Microchip (MPU, EPROM, EEPROM)

Mitsubishi (EPROM, EEPROM)

Mosel (MPU, EEPROM)

MXIC (EPROM, EEPROM)

NEC (EPROM, EEPROM)

NS (PLD, EPROM)

OKI (EPROM, EEPROM)

PDK (MPU)

Philips (MPU)

PMC (EEPROM)

PTC (EEPROM)

Ricoh (EPROM)

Samsung (MPU, EPROM, EEPROM)

SEEQ (EPROM, EEPROM)

SGS Thomson (PLD, EPROM, EEPROM)

Signetics (EPROM)

SMOS (EPROM

Sony (EPROM)

Sonix (MPU)

Spansion (EEPROM)

SST (MPU, EEPROM)

ST (EPROM, EEPROM)

STC (MPU)

Stand (RAM)

Syncmos (MPU, EEPROM)

TI (EPROM, EEPROM)

Topro (MPU)

Toptek (MPU)

Toshiba (EPROM, EEPROM)

Versachip (MPU)

VLSI (PLD, EPROM, EEPROM)

Winbond (MPU, RAM, EEPROM)

WSI (EPROM)

Xicor (EEPROM)

Package Include:

1pc x TOP3000 universal programmer

1pc x USB 2.0 cable (USB 1.1 compatible)

1pc x 5V/2A AC adapter

1pc x TOPwin software CD

1pc x English User Manual

CH000548
€98.21

TOP3000 Universal Programmer for MCU and EPROMs Programming ECU Chip Tunning

CM141 LeadFree Titanium Alloy Solder Soldering Pot Desoldering Bath 900W 110V

LEAD-FREE TITANIUM ALLOY SOLDERING POT

Operation instruction

Login to Download: * Manual Download

Our Lead-free titanium alloy soldering pot passed by SGS, built-in advanced microcomputer digital control and display system, make it more safe, more steady and more accurate. Its a good tool for electronic fields.

FEATURES:

* With big power heater, only within 25minutes to reach 450? from room temperature, (Different items with a little different heating time.)

* With advanced microcomputer digital control and double displays. make it more accurate heating and fast temperature returning capability.

* The boiler made of titanium alloy, can resist high temperature, cauterization and abrasion, largely prolong the life.

* With temperature setting and locking function, will not be affected by wrong operation.

* The setting value will be saved for long time, and can not be affected by power on or off. With auto sleeping function, prolong the machines life.

* With malfunction alarm.

Working conditions:

Working voltage: AC22010V

Working temperature: 0-55?

Working temperature: < 90% no dew

WARNING:

1. The soldering pot must be put on the balanced and ovenproof working desk, prevent the glowing tin go out of the pot. And also take care of the hot tin and the hot body.

2. Do not put other pb items together with the lead-free soldering pot, prevent pb pollution. If cause the products do not eligible, then we wont take on this liability.

3. It cant be used where it will be exposed to ignitable or corrosive materials and gases.

4. If you need to move the soldering pot, please turn off the switch and move it after the pot turn cool.

5. The pot is a hot equipment, if you no need to use, please shut off the switch, and put out the plug.

6. In order to keep it safe and prolong the life, its better stop working after it has worked more than 12hours.

7. Do not heating the pot when its empty, and use the power supplier with grounding cord.

8. The pot is made of titanium which import from Japan, after it is heated by hot temperature, the color will turn to golden or blue, its natural for the material.

OPERATION:

1. Set temperature:

Press the * button, the left LED will display ?,and the right LED will display numerical value, then press the + or -button, temperature will go up or down. Press * button, the value of temperature will be saved.

2. Microcomputer adjusting itself

If the temperature has obvious discrepancy, we can adjust the inside P, I, D value, it will make the pot with accurate control, the followings are two ways of P, I, D adjusting:

A. Auto adjusting

Keep pressing + button, then press * , the left LED will display AT; the right LED will display _ _ _. Then press ? or + change the _ _ _ to AT, this time please press * for 3 times, then the pot will begin P, I, D adjusting itself. Usually it will take for about 15-30 minutes to finish this adjusting, during this adjusting the temperature will fluctuate obviously, but its no wonder. Usually, we do not recommend the users use P, I, D adjusting.

B. Adjust the value of P, I, D by manual (Do not advise users use this way, its fit for the engineers who know P, I, D very well, otherwise maybe cause bad temperature control. If really need, we just recommend the first way.) The operation as follows: Keep pressing + , then press * , the LED will display above (A) setting mode, press * again the LED will display the value of P, I, D. Manual adjusting just can be set the original value.

Remarks: The original of P, I, D value is: P=20, I=80, D=20; If the temperature in

confusion, please set the P, I, D value as original value.

3. Calibration between display and real temperature.

After the heater was replaced or the sensor was oxidated, the temperature will occur warp, the users need to calibrate the pot termly, and as the follow steps:

A. Press CAL button (If your pot without this button, please open the front cover, there is a black button on the PCB of temperature control, that is CAL), the right LED will display OFF, keep pressing ? , and press * at the same time, the left LED will display LOC, the right LED will display -3-, then press * for 3 times (just this button, do not press any other buttons), the LED will display: The first time: Left ?H, right 999; The second time: Left ?L, right 0; The third time: Left ?L, then please input the value of temperature compensation. This value is the warp between display temperature and real temperature. For example, the real temperature is more 5? higher than the display temperature, it can use ? to set -5; If the real temperature is 5? less than the display temperature, it can use + to set 5.

B. The warp temperature is the value to input, after finish setting, press * again, the set value will be saved. Then press CAL (If your pot without this button, please open the front cover, there is a black button on the PCB of temperature control, that is CAL), it will come into the ordinary display mode.

TROUBLE SHOOTING:

1. Turn on the switch but no reflection, please check the fuse, and the plug.

2. The LED display setting temperature, but the pot temperature wont go up, it means that the heater is open circuit.

3. The pot display Err when the power switch is turned on, it means that the sensor is open circuit.

CH000318
€177.78

CM141 Lead-Free Titanium Alloy Solder Soldering Pot Desoldering Bath 900W 110V