DX0001 Adapter for XELTEK SuperPro 6100N

TNM5000 Universal Programmer Introduction

Login to Download: * Programmer latest Software

User Manual Device List Nand Software Utility Software for RS232 & USB Bl a ster Emulation

? 23000 Supported Devices Flash Memory (Parallel / Nand /Serial) , EPROM , EEPROM , Serial EEPROM , Microcontroller , NVRAM , FRAM , CPLD , PLD , FPGA).

? 48-Pins ZIF Socket with Pin Continuity tester & 10-Pins ISP/JTAG Connector.

? USB 2.0 High Speed ,Program 1 Gbit Nand Flash less than 50 sec , Reading Serial Flash memory with 6 Mbit/Sec Speed.

? Auto detection of all flash Memories/Microcontrollers with Device ID.

? User friendly software for Windows XP/VISTA/7/8 (32,64 bits).

? Multiple Programming is possible by attaching 2 or more Programmers to one PC.

? Very low cost Main Unit & Low cost adaptors.

? Special Abilities like, Altera US,B-B.l*a*s.ter Emulation for Quartus Software, Serial Port Emulation , Vehicle ECU , Immoblizer & Dashboard microcontroller Support.

Parallel Flash Memories: up to 56 pins parallel flash memories are supported by TNM5000. it Supports different kind of packages (PLCC , TSOP1 , TSOP2 ,VSOP & ...).

All Flashes can be automatically detected by software in case of unreadable device names. By using a single adaptor for all 32-48 pins TSOP flashes , user only need 1 adaptor for over 2000 flash chips.

Nand Flash Memories: TNM5000 has an additional Nand+ software , specially designed for Nand flash memories. Nand+ Software has one of the most complete list of Nand flash Memories with algorithms for correction of bad data in MLC Nand Flashes. TNM5000 is one of the fastest Nand Programmers in the world with Read & Write Speed up to 8 MegaByte per Second. All Nand Flashes can be automatically detected by software in case of unreadable or remarked device names.

Serial Flash Memories: All 8-16 Pins Serial SPI flash memories are supported by TNM5000. All SPI flash Memories can be detected automatically by software in case of unreadable device names. It reads & programs SPi flashes with maximum safe speed on ZIF (6-7 Mbit/second) . Also it Unprotects the write protected flashes before writing data to it.

Microcontrollers:

ATMEL: All AVR 8 bits chips (ATMEGA/ATTINY/AT90S) are supported on ZIF Scocket & by ISP cable. High Voltage Parallel on ZIF Programming of AVR up to 64 pins is supported. newly introduced ATXMEGA Series are supported by both PDI & JTAG Method. Old C51 series & new single cycle C51 series are completely supported. All the above series can be detected automatically by TNM5000. ARM7 programming by JTAG is supported.

Microchip: One of the most complete device list for microchip PIC microcontrollers including all PIC12F /PIC12C /PIC16C / PIC16F / PIC18F / DPIC33F / J & K Series. Devices up to 40 Pins can be programmed on ZIF , All PICs can be detected automatically & programmed by ISP cable.

Others: ST, SST, Philips (NXP) , Motorola , Syncmos, Silicon Lab , ICSI , Infineon , Intel , Winbond & ...

Automotive MCUS: Supporting of ST10F & TMS370 Series by ISP cable for many BOSCH/VALEO/SAGEM ECUs (complete ST10F support of XPROG-m programmer device list). supporting of siemense & infineon SAK-C167 connected to 44 or 48 pins flash (Siemense/BOSCH/SAGEM S2000 ECU) like HSE FlasHit Programmer. Supporting NEC & Motorola Devices for Dashboards.

PLD/CPLD/FPGA: Supporting All ALTERA JTAG Devices by emulation of USB B l a s t e r Programmer in Quartus Software. Supporting of Xilinx CPLD/FPGA with jed file. Fast Xilinx FPGA configuration with bit file. Supporting of GAL/PALCE Devices with special option for PALCE unlocking.

Software: With multiple language support (English / Chinese / Russian /polska /Arabic / French /FARSI). More languages & Devices can be added by customer request. You Can Download Software & run it in Demo mode to evaluate it.

Package List:

1 x TNM5000 Programmer

1 x usb cable

1 x software CD

Mini ST-Link V2 stlink Emulator Downloader STM8 STM32 With Cover + Dupont Cable

(A random colour will be sent.)

Login to Download: Download software

DESCRIPTION:

Mini ST-LINK/V2,which is fully compatible with the official functions,support for automatic upgrades.

Support all series of STM32 and STM8.

SPECIFICATIONS:

COLOUR: A random colour will be sent.

Support all STM32 series SWD interface debug.

Support all STM8 series debug.

Support firmware upgrade automatically

Increase the electrostatic protection circuit, it can protect output I/O port, not afraid of static electricity.

Supports development environment:

ST-LINK Utility 2.0 and the version latest than it.

STVD 4.2.1 and the version latest than it.

STVP 3.2.3 and the version latest than it.

IAR EWARM V6.20 and the version latest than it.

IAR EWSTM8 V1.30 and the version latest than it.

KEIL RVMDK V4.21 and the version latest than it.

PACKAGE INCLUDES:

1x ST-Link V2 Emulator Downloader

4x 20 cm Female - Female Dupont cables

48 pin Lock clasp Programmer for RT809H TNM5000 XELTEK 610P 611S 6100N BeeProg2

Texas MSP430 USB-Debug-Interface MSP-FET430UIF

DX1045-1 Adapter for XELTEK SuperPro 6100N

TNM5000 Universal Programmer Introduction

Login to Download: * Programmer latest Software

User Manual Device List Nand Software Utility Software for RS232 & USB Bl a ster Emulation

? 23000 Supported Devices Flash Memory (Parallel / Nand /Serial) , EPROM , EEPROM , Serial EEPROM , Microcontroller , NVRAM , FRAM , CPLD , PLD , FPGA).

? 48-Pins ZIF Socket with Pin Continuity tester & 10-Pins ISP/JTAG Connector.

? USB 2.0 High Speed ,Program 1 Gbit Nand Flash less than 50 sec , Reading Serial Flash memory with 6 Mbit/Sec Speed.

? Auto detection of all flash Memories/Microcontrollers with Device ID.

? User friendly software for Windows XP/VISTA/7/8 (32,64 bits).

? Multiple Programming is possible by attaching 2 or more Programmers to one PC.

? Very low cost Main Unit & Low cost adaptors.

? Special Abilities like, Altera US,B-B.l*a*s.ter Emulation for Quartus Software, Serial Port Emulation , Vehicle ECU , Immoblizer & Dashboard microcontroller Support.

Parallel Flash Memories: up to 56 pins parallel flash memories are supported by TNM5000. it Supports different kind of packages (PLCC , TSOP1 , TSOP2 ,VSOP & ...).

All Flashes can be automatically detected by software in case of unreadable device names. By using a single adaptor for all 32-48 pins TSOP flashes , user only need 1 adaptor for over 2000 flash chips.

Nand Flash Memories: TNM5000 has an additional Nand+ software , specially designed for Nand flash memories. Nand+ Software has one of the most complete list of Nand flash Memories with algorithms for correction of bad data in MLC Nand Flashes. TNM5000 is one of the fastest Nand Programmers in the world with Read & Write Speed up to 8 MegaByte per Second. All Nand Flashes can be automatically detected by software in case of unreadable or remarked device names.

Serial Flash Memories: All 8-16 Pins Serial SPI flash memories are supported by TNM5000. All SPI flash Memories can be detected automatically by software in case of unreadable device names. It reads & programs SPi flashes with maximum safe speed on ZIF (6-7 Mbit/second) . Also it Unprotects the write protected flashes before writing data to it.

Microcontrollers:

ATMEL: All AVR 8 bits chips (ATMEGA/ATTINY/AT90S) are supported on ZIF Scocket & by ISP cable. High Voltage Parallel on ZIF Programming of AVR up to 64 pins is supported. newly introduced ATXMEGA Series are supported by both PDI & JTAG Method. Old C51 series & new single cycle C51 series are completely supported. All the above series can be detected automatically by TNM5000. ARM7 programming by JTAG is supported.

Microchip: One of the most complete device list for microchip PIC microcontrollers including all PIC12F /PIC12C /PIC16C / PIC16F / PIC18F / DPIC33F / J & K Series. Devices up to 40 Pins can be programmed on ZIF , All PICs can be detected automatically & programmed by ISP cable.

Others: ST, SST, Philips (NXP) , Motorola , Syncmos, Silicon Lab , ICSI , Infineon , Intel , Winbond & ...

Automotive MCUS: Supporting of ST10F & TMS370 Series by ISP cable for many BOSCH/VALEO/SAGEM ECUs (complete ST10F support of XPROG-m programmer device list). supporting of siemense & infineon SAK-C167 connected to 44 or 48 pins flash (Siemense/BOSCH/SAGEM S2000 ECU) like HSE FlasHit Programmer. Supporting NEC & Motorola Devices for Dashboards.

PLD/CPLD/FPGA: Supporting All ALTERA JTAG Devices by emulation of USB B l a s t e r Programmer in Quartus Software. Supporting of Xilinx CPLD/FPGA with jed file. Fast Xilinx FPGA configuration with bit file. Supporting of GAL/PALCE Devices with special option for PALCE unlocking.

Software: With multiple language support (English / Chinese / Russian /polska /Arabic / French /FARSI). More languages & Devices can be added by customer request. You Can Download Software & run it in Demo mode to evaluate it.

Package List:

1 x TNM5000 Programmer

1 x USB Cable

1 x software CD

1 x TQFP44-DIP44 Adapter

1 x TQFP32-DIP28 Adapter

1 x TSOP48-DIP48 Adapter

1 x SOP44-DIP44 Adapter

1 x SOP28-DIP28 300mil adapter

1 x SOP8-DIP8 200-208mil adapter

1 x SOP8-DIP8 150mil adapter

1 x TSSOP28 to DIP28 adapter

1 x TSSOP8 to DIP8 adapter

1 x SOP16 TO DIP16 adapter

1 x SOP20-DIP20(200~208mil)adapter

1 x PLCC44-DIP44 adapter

1 x PLCC32-DIP32 adapter

1 x PLCC28-DIP24 Adapter

1 x PLCC20-DIP20 Adapter

1 x SOP4/SOP28-SSOP4/SSOP28simple Adapter

1 x SOP16/SOP8 simple Adapter

1 x SOIC8 SOP8 To DIP8 CLIP

1 x IC Chip Extractor

XELTEK SuperPRO 610P Universal Programmer can use for items list:

Login to Download: Download software

Xeltek SuperPro 610P is a device for programming EPROM, Paged EPROM, Parallel and Serial EEPROM, FPGA Configuration PROM, FLASH memory (NOR, NAND), BPROM, NVRAM, SPLD, CPLD, EPLD, FWH, microcontrollers, standard micrologic circuits.

Features

Universal 48-pin driver supports today's most complex devices.

Possibility to connect 99% of the existing microelectronic circuits in case you buy a corresponding adapter.

Programs devices with Vcc as low as 1.2V.

In-system programming (ISP / ICP) capability.

Programming / testing features for TTL/CMOS logic ICs and memories.

Software updates.

RoHS compatible, CE, ISO 9001, ISO 14001 certificates.

Application

Device repair ? re-flashing microchips, microcontrollers.

Flashing new microchips.

Serial manufacturing - microchips, microcontrollers programming.

Restoring data from microchips of solid-state drive.

Technical Specifications

Input/Output built-in 48 pin connector

Package Types DIP, SDIP, PLCC, JLCC, SOIC, QFP, TQFP, PQFP, VQFP, TSOP, SOP, TSOPII, PSOP, TSSOP, SON, EBGA, FBGA, VFBGA, BGA, CSP, SCSP

Interface USB 2.0

Software compatible OS Windows XP, Windows Vista, Windows 7, Windows 8 (32/64 bit)

Power Supply Input 90 V-250 V AC, output 12 V DC/1.5 A

Size, L W H 178 130 40 mm

Weight 0.38 kg (without package)

Package Contents

USB Interfaced Universal Programmer Xeltek SuperPro 610P ? 1 pc.

AC Power Adapter ? 1 pc.

USB Cable ? 1 pc.

CD with Software ? 1 pc.

User Manual ? 1 pc.

Optional Accessories

Adapters

Compact-Flash (CF) card

DX3013 Adapter for XELTEK SuperPro 6100N

XELTEK SuperPRO 610P Universal Programmer can use for items list:

Login to Download: Download software

Xeltek SuperPro 610P is a device for programming EPROM, Paged EPROM, Parallel and Serial EEPROM, FPGA Configuration PROM, FLASH memory (NOR, NAND), BPROM, NVRAM, SPLD, CPLD, EPLD, FWH, microcontrollers, standard micrologic circuits.

Features

Universal 48-pin driver supports today's most complex devices.

Possibility to connect 99% of the existing microelectronic circuits in case you buy a corresponding adapter.

Programs devices with Vcc as low as 1.2V.

In-system programming (ISP / ICP) capability.

Programming / testing features for TTL/CMOS logic ICs and memories.

Software updates.

RoHS compatible, CE, ISO 9001, ISO 14001 certificates.

Application

Device repair ? re-flashing microchips, microcontrollers.

Flashing new microchips.

Serial manufacturing - microchips, microcontrollers programming.

Restoring data from microchips of solid-state drive.

Technical Specifications

Input/Output built-in 48 pin connector

Package Types DIP, SDIP, PLCC, JLCC, SOIC, QFP, TQFP, PQFP, VQFP, TSOP, SOP, TSOPII, PSOP, TSSOP, SON, EBGA, FBGA, VFBGA, BGA, CSP, SCSP

Interface USB 2.0

Software compatible OS Windows XP, Windows Vista, Windows 7, Windows 8 (32/64 bit)

Power Supply Input 90 V-250 V AC, output 12 V DC/1.5 A

Size, L W H 178 130 40 mm

Weight 0.38 kg (without package)

Package Contents

1 * XELTEK SuperPro 610P Programmer

1 * AC Adapter: Input AC 100V- 240V; Output: 12V/1.5A

1 * USB Cable

1 * CD Software

1 * TSOP48 Adapter

1 * SOP28-DIP28 (300mil) Adaptador

1 * SOP20-DIP20 (200mil) Adaptador

1 * SOP8-DIP8 (200mil) Adaptador

1 * SOP16-DIP16 (150mil) Adaptador

1 * SOP8-DIP8 (150mil) Adaptador

1 * TSSOP8-DIP8 (170mil) Adaptador

1 * PLCC44-DIP44

1 * PLCC44-DIP40

1 * PLCC32-DIP32

1 * PLCC28-DIP28

1 * PLCC28-DIP24

1 * PLCC20-DIP20

1 * SOP8-DIP8 Simple Adaptador

1 * QFN8 WSON8 Simple Adaptador

1 * MSOP8/SSOP8/SOP8/SOP16-DIP16 Simple Adaptador

2 * SSOP4-28PIN 0.65mm / SOP4-28PIN 1.27mm Simple Adaptador

1 * LCD LED screen EDID code

1 * SOP8 Clamp Test

1 * IC Chip Extractor

This adapter can use on RT809H XGecu TL866II Plus, T56 programmer and other universal programmers such as Superpro, TNM, TOP, GQ-4X, Stager, SOFI and so on.

Applicable IC Dimensions(REF.) : both 6*5MM

Applicable IC Package:

-QFN8

-MLF8

-MLP8

-WSON8

-DFN8

Pitch: 1.27mm

DX1027 Adapter for XELTEK SuperPro 6100N